Targets

The target block is required. There may be any number of targets — one price per line. The order of the targets in the text becomes their numbers: the first line is take-profit #1, the second is #2 and so on; these numbers are later used in the /change_tp1_to_… commands and in the notifications “Take-profit 1/3 reached”.

Keywords

At the start of a line, case does not matter: tp, tp targets, take profit, take-profit, sell, цели, продажа. TPs:, Take profits:, Sell targets: and Цель: are also understood (the last one if the post has no ordinary Цели: heading). Emoji and bullets in front of the word are removed: 🎯 TP:.

The block heading must occur once: TP: and Take profit: in the same post is an error.

Right and wrong

Right	Wrong	What happens
TP: 87000 88500 90000	TP: 87000 / 88500 / 90000	Only the first number is taken from a line — one target remains
TP1: 87000 TP2: 88500	TP1 87000 TP2 88500	Without a separator after the number the digit sticks to the price: the targets become 187000 and 288500 — with no error
1) 87000, 1. 87000, Take profit 2 - 88500, 1️⃣ 87000	Take profit2 88500	The same sticking
TP: 87000	TP: … and below Take profit: …	Two headings of the same block
TP: 87000 88500 SL: 82900	TP: 87000 RR 1:2 SL: 82900	A line with a number inside the block becomes a false target
TP: 87500, 87 500, 0,545	TP: 87,500	One group of three digits after a comma can be read two ways — the bot refuses; a decimal comma (0,545) is allowed

Lines without digits inside the block are skipped. Shares per target (how much to close at each take-profit) are not written in a channel signal — each subscriber sets them on their side (Distribution across targets).

Where the targets must be

For LONG all targets are entirely above all entry prices, for SHORT — entirely below. A target between the entry prices, or on the same side as the stop, is an error with an explanation. For spot (without leverage) targets can only be above the entry.

Example

Three numbered targets — the first numbered line serves as the block heading, a separate TP: line before it is not needed:

#BTCUSDT
Leverage: 10x
Entry: 85000
TP1: 87000
TP2: 88500
TP3: 90000
SL: 82900

Common mistakes and what the bot says

• “Value not found for TAKE_PROFIT” — there is no line with a target keyword, or none of the lines in the block contain digits.
• “More than one keyword found for TAKE_PROFIT. Found: …” — two target headings (TP: and Take profit:). Keep one.
• “Take-Profit (84500) falls within the entry price range (85000 - 84200). TP must be entirely above entry (for LONG) or entirely below entry (for SHORT). Check the TP and Entry prices.”
• “Take-Profit (84000) is below the entry price (85000). Leverage not specified — signal recognized as SPOT, where only LONG is available (TP must be above entry). If this is SHORT — specify leverage (e.g. 5x).”
• The signal card shows take-profit 187000 instead of 87000 — a number without a separator. Write TP1: 87000 or 1) 87000, and simplest of all — without numbering.
• Only the first of three targets was taken — the targets were on one line separated by /. Each target goes on its own line.
• You made a mistake in a target of a published signal — /change_tp1_to_87500 as a reply to the post (Commands in the channel); editing the post is pointless.